Omron STC-SC152POEHS 1.4MP GigE, Color Camera (CCD Sensor: ICX267AK)

The STC-SC152POEHS is part of Omron/Sentech's Brand New Power over Ethernet High Speed GigE camera series. It features a 1/2" color SXGA sensor, 34fps and communication over a 6 pin Hirose or Ethernet connector. The STC-SC152POEHS boasts a compact 35(w) x 35(H) x 55.9 (D) mm size, a user-programmable Area of Interest (AOI) and a Gamma Table that can be imported. This camera meets all industry standards for GigE Vision® and GenICam™, and is compatible with all standard industry drivers. The GigE PoEHS series is available now at an extremely low cost.

Features:

• User Programmable AOI
• High Speed Power Over Ethernet
• 1.3 Megapixel Resolution with 34 fps

STC-SC152POEHS Specifications
Imager	1/2” interline SXGA color progressive CCD: ICX267AK
Total Picture Element	1434 (H) x 1050 (V)
Active Picture Element	SXGA: 1360 (H) x 1040 (V)
Chip Size	7.6 (H) x 6.2 (V) mm
Cell Size	4.65 (H) x 4.65 (V) um
Scanning System	Progressive
Vertical Frequency	34.23358 Hz at full resolution; 0.55789 to 139.93433 Hz changeable via the communication; Maximum frame rate is dependent on the AOI setting; Maximum frame rate of the camera (139.93433 Hz) is 104 vertical resolution AOI setting.
Horizontal Frequency	34.0860 Hz
Pixel Frequency	65.453333 MHz
Noise Level
@ 8bit output	<= 3 Digit (Gain 0 dB)
@ 10bit output	<= 12 Digit (Gain 0 dB)
@ 12bit output	<= 48 Digit (gain 0 dB)
Minimum Scene Illumination	16.3 Lux at F1.2, 34.23358 Hz
Sync System	Internal
Video Output	Digital 8 ,10 or 12 bit Raw Data or RGB 8 bit
Interface	PoE: IEEE802.3af CLASS3 (1000BASE-T)
Protocol	GigE Vision 1.2 and GeniCam 2.0 compliant
Exposure Time	Preset continuous mode: 10 seconds to 16,777,216 seconds; Preset trigger mode: 10 seconds to 16,777,216 seconds; Pulse width mode: 10 seconds to Unlimited.
ALC	Electronic iris and AGC (ON/OFF)
Gain	0 to 18.309 dB
Gamma	Gamma 1.0 (Factory default) or downloadable gamma table
AOI Function	Programmable AOI setting via the communication
Smear Reduction	Selectable ON/OFF via the communication
Color Interpolation	Available on RGB output
White Balance Function	Auto, Manual, and push to set white balance is available on both Raw Data output and RGB output.
Operation Mode	Edge preset trigger, pulse width trigger (unlimited exposure time)
Communication	UART communication through Ethernet Port
I/Os	One opt isolated input and two open collector outputs
Power
Input Voltage	+10.8 to +26.4Vdc through power/IO connector or Power Over Ethernet; (Auto detection with power/IO connector prioritized)
Consumption	12V: 3.5W / 3.2W, PoE: 3.7W / 3.5W
Dimensions	35 (W) x 35 (H) x 57.3 (D) mm excluding connectors
Optical Filter	IR cut filter on
Optical Center Accuracy	Positional accuracy in H and V directions: +/- 0.3 mm; Rotational accuracy of H and V: +/- 1.5 deg.
Material	Aluminum (AC)
Lens Mount	C Mount
Connectors	RJ45 connector; Power/IO connector: HR10A-10R-6PB (Hirose) or equivalent
Camera Mount Screws	Two ¼” Tripod screw holes (one each on top and bottom plate); Twelve M4 screw holes (four each on top, bottom, and two each on both side plates)
Weight	Approx. 130
Operating Temperature
Minimum	Environmental Temperature: -5 deg. C
Maximum	Environmental Temperature: 35 deg. C or camera housing temperature (Top Plate) : 65 deg. C
Storage Temperature	Environmental Temperature: -30 to 65 deg. C
Vibration	20Hz to 200Hz to 20Hz (5min/cycle), acceleration 10G, 3 directions 30 min. each
Shock	Acceleration 38G, half amplitude 6ms, 3 directions, 3 times each
Standard Compliancy	EMS: EN61000-6-2, EMI: EN55011
RoHS	RoHS compliant