The STC-SB152POE is part of Sentech's Brand New Power over Ethernet GigE camera series. It features a 1/2" monochrome UXGA sensor, 19fps and communication over a 6 pin Hirose or Ethernet connector. The STC-SB152POE boasts a compact 35(w) x 35(H) x 55.9 (D) mm size, a user-programmable Area of Interest (AOI) and a Gamma Table that can be imported. This camera meets all industry standards for GigE Vision® and GenICam™, and is compatible with all standard industry drivers. The GigE PoE series is available now at an extremely low cost.
Features:
STC-SB152POE Specifications | |
Imager | 1/2" interline SXGA monochrome progressive CCD: ICX205AL |
Total Picture Element | 1434 (H) x 1050 (V) |
Active Picture Element | SXGA: 1360 (H) x 1040 (V) |
Cell Size | 4.65 (H) x 4.65 (V) µm |
Scanning System | Progressive |
Vertical Frequency (Frame Rate) | 19.25954 Hz at full resolution 0.31387 to 77.03817 Hz changeable via the communication (Frame rate depends on the AOI setting) Maximum frame rate (77.03817 Hz) is when vertical resolution AOI setting is 199. |
Horizontal Frequency | 20.5688 kHz |
Pixel Frequency | 36.818175 MHz |
Noise Level | |
@ 8bit output
|
≤ 3 Digit (Gain 0 dB) |
@ 10bit output
|
≤ 12 Digit (Gain 0 dB) |
@ 12bit output
|
≤ 48 Digit (Gain 0 dB) |
Minimum Scene Illumination | TBD Lux at F1.2, 19.25954Hz |
Sync System | Internal |
Video Output | Digital 8, 10 or 12 bit Raw Data |
Interface | PoE : IEEE802.3af CLASS2 (1000BASE-T) |
Protocol | GigE Vision® 1.2 and GenICam™ 2.0 compliant |
Exposure Time | Preset continuous mode: 10 useconds to 16,777,215 useconds Preset trigger mode: 10 useconds to 16,777,215 useconds Pulse width mode: 10 useconds to Unlimited |
ALC | AE and AGC (ON/OFF) |
Gain | 0 to 20.4 dB |
Gamma | Gamma 1.0 (Factory default) or uploadable gamma table |
AOI Function | Variable AOI setting via the communication |
Smear Reduction | Selectable ON/OFF via the communication |
Color Interpolation | N/A |
White Balance Function | N/A |
Trigger Mode | Edge preset trigger, Pulse width trigger (unlimited long exposure) |
Communication | UART communication through Ethernet port |
I/Os | One opt isolated input and two open collector outputs |
Power | |
Input Voltage
|
+10.8 to +26.4 Vdc via power-I/O connector or Power over Ethernet (Power-I/O connector power supply is prioritized.) |
Consumption
|
12V: 2.9W / 2.8W, PoE: 3.3W / 3.1W |
Dimensions | 35 (W) x 35 (H) x 55.9(D) mm excluding connectors |
Optical Filter | No Filter |
Optical Center Accuracy | Positional accuracy in H and V directions: +/- 0.3 mm Rotational accuracy of H and V: +/- 1.5 deg. |
Material | Aluminum (AC) |
Lens Mount | C mount |
Connectors | RJ45 connector; Power/IO connector: HR10A-10R-6PB (Hirose) or equivalent |
Camera Mount Screws | Two 1/4” Tripod screw holes: (One on each top and bottom plate), Twelve M4 screws holes: (Four on each top and bottom plate, two on each side plate) |
Weight | Approx. 130 |
Operating Temperature | |
Minimum
|
Environmental Temperature -5⁰C |
Maximum
|
Camera housing temperature (top plate) shall not exceed 65⁰C (This corresponds to an environmental temperature of approximately 35⁰C) |
Storage Temperature | Environmental Temperature: -30⁰C to 65⁰C |
Vibration | 20Hz to 200Hz to 20Hz (5min./cycle), acceleration 10G, 3 directions 30 min. each |
Shock | Acceleration 38G, half amplitude 6ms, 3 directions 3 times each |
Standard Compliancy | EMS: EN61000-6-2, EMI: EN55011 |
RoHS | RoHS Compliant |