The STC-SB152POEHS is part of Sentech's Brand New Power over Ethernet High Speed GigE camera series. It features a 1/2" monochrome SXGA sensor, 34fps and communication over a 6 pin Hirose or Ethernet connector. The STC-SB152POEHS boasts a compact 35(w) x 35(H) x 55.9 (D) mm size, a user-programmable Area of Interest (AOI) and a Gamma Table that can be imported. This camera meets all industry standards for GigE Vision® and GenICam™, and is compatible with all standard industry drivers. The GigE PoEHS series is available now at an extremely low cost.
Features:
STC-SB152POEHS Specifications | |
Imager | 1/2” interline SXGA monochrome progressive CCD: ICX267AL |
Total Picture Element | 1434 (H) x 1050 (V) |
Active Picture Element | SXGA: 1360 (H) x 1040 (V) |
Chip Size | 7.6 (H) x 6.2 (V) mm |
Cell Size | 4.65 (H) x 4.65 (V) um |
Scanning System | Progressive |
Vertical Frequency | 34.23358 Hz at full resolution; 0.55789 to 139.93433 Hz changeable via the communication; Maximum frame rate is dependent on the AOI setting; Maximum frame rate of the camera (139.93433 Hz) is 104 vertical resolution AOI setting. |
Horizontal Frequency | 34.0860 Hz |
Pixel Frequency | 65.453333 MHz |
Noise Level | |
@ 8bit output
|
<= 3 Digit (Gain 0 dB) |
@ 10bit output
|
<= 12 Digit (Gain 0 dB) |
@ 12bit output
|
<= 48 Digit (gain 0 dB) |
Minimum Scene Illumination | 0.50 Lux at F1.2, 34.23358 Hz |
Sync System | Internal |
Video Output | Digital 8 ,10 ,12 bit Raw Data |
Interface | PoE: IEEE802.3af CLASS3 (1000BASE-T) |
Protocol | GigE Vision 1.2 and GeniCam 2.0 compliant |
Exposure Time | Preset continuous mode: 10 seconds to 16,777,216 seconds; Preset trigger mode: 10 seconds to 16,777,216 seconds; Pulse width mode: 10 seconds to Unlimited. |
ALC | Electronic iris and AGC (ON/OFF) |
Gain | 0 to 18.309 dB |
Gamma | Gamma 1.0 (Factory default) or downloadable gamma table |
AOI Function | Programmable AOI setting via the communication |
Smear Reduction | Selectable ON/OFF via the communication |
Color Interpolation | N/A |
White Balance Function | N/A |
Trigger Mode | Edge preset trigger, pulse width trigger (unlimited exposure time) |
Communication | UART communication through Ethernet Port |
I/Os | One opt isolated input and two open collector outputs |
Power | |
Input Voltage
|
+10.8 to +26.4Vdc through power/IO connector or Power Over Ethernet; (Auto detection with power/IO connector prioritized) |
Consumption
|
12V: 3.5W / 3.2W, PoE: 3.7W / 3.5W |
Dimensions | 35 (W) x 35 (H) x 57.3 (D) mm excluding connectors |
Optical Filter | IR cut filter on |
Optical Center Accuracy | Positional accuracy in H and V directions: +/- 0.3 mm; Rotational accuracy of H and V: +/- 1.5 deg. |
Material | Aluminum (AC) |
Lens Mount | C Mount |
Connectors | RJ45 connector; Power/IO connector: HR10A-10R-6PB (Hirose) or equivalent |
Camera Mount Screws | Two ¼” Tripod screw holes (one each on top and bottom plate); Twelve M4 screw holes (four each on top, bottom, and two each on both side plates) |
Weight | Approx. 130 |
Operating Temperature | |
Minimum
|
Environmental Temperature: -5 deg. C |
Maximum
|
Environmental Temperature: 35 deg. C or camera housing temperature (Top Plate) : 65 deg. C |
Storage Temperature | Environmental Temperature: -30 to 65 deg. C |
Vibration | 20Hz to 200Hz to 20Hz (5min/cycle), acceleration 10G, 3 directions 30 min. each |
Shock | Acceleration 38G, half amplitude 6ms, 3 directions, 3 times each |
Standard Compliancy | EMS: EN61000-6-2, EMI: EN55011 |
RoHS | RoHS compliant |