The STC-SC500POE is part of Sentech's Brand New Power over Ethernet GigE camera series. It features a 2/3" color UXGA sensor, 15fps and communication over a 6 pin Hirose or Ethernet connector. The STC-SC500POE boasts a compact 35(w) x 35(H) x 55.9 (D) mm size, a user-programmable Area of Interest (AOI) and a Gamma Table that can be imported. This camera meets all industry standards for GigE Vision® and GenICam™, and is compatible with all standard industry drivers. The GigE PoE series is available now at an extremely low cost.
Features:
STC-SC500POE Specifications | |
Imager | 2/3" interline QSXGA color progressive CCD: ICX625AQ |
Total Picture Element | 2536 (H) x 2068 (V) |
Active Picture Element | QSXGA: 2448 (H) x 2058 (V) |
Cell Size | 3.45 (H) x 3.45 (V) µm |
Scanning System | Progressive |
Vertical Frequency (Frame Rate) | 15.18586 Hz at full resolution 0.48175 to 60.71422 Hz adjustable via the communication (Frame rate depends on the AOI setting.) Maximum frame rate (60.71422 Hz) is when vertical resolution AOI setting is 128. |
Horizontal Frequency | 31.1284 kHz |
Pixel Frequency | 81.8182 MHz |
Noise Level | |
@ 8bit output
|
≤ 4 Digit (Gain 0 dB) |
@ 10bit output
|
≤ 15 Digit (Gain 0 dB) |
@ 12bit output
|
≤ 60 Digit (Gain 0 dB) |
Minimum Scene Illumination | TBD Lux at F1.2, 15Hz |
Sync System | Internal |
Video Output | Digital 8, 10 or 12 bit Raw data or RGB 8 bit |
Interface | PoE : IEEE802.3af CLASS2 (1000BASE-T) |
Protocol | GigE Vision® 1.2 and GenICam™ 2.0 compliant |
Exposure Time | Preset continuous mode: 10 useconds to 16,777,215 useconds Preset trigger mode: 10 useconds to 16,777,215 useconds Pulse width mode: 10 useconds to Unlimited |
ALC | AE and AGC (ON/OFF) |
Gain | 0 to 18.309 dB |
Gamma | Gamma 1.0 (Factory default) or uploadable gamma table |
AOI Function | Variable AOI setting via the communication |
Smear Reduction | Selectable ON/OFF via the communication |
Color Interpolation | Available on RGB Output |
White Balance Function | Auto, Manual, Push to Set White Balance are available on both raw data and RGB outputs |
Operation Mode | Edge preset trigger, Pulse width trigger (unlimited long exposure) |
Communication | UART communication through Ethernet port |
I/Os | One opt isolated input and two open collector outputs |
Power | |
Input Voltage
|
+10.8 to +26.4 Vdc via power-I/O connector or Power over Ethernet (Power-I/O connector power supply is prioritized.) |
Consumption
|
12V: 4.1W / 3.5W, PoE: 4.5W / 3.8W |
Dimensions | 35 (W) x 35 (H) x 55.9(D) mm excluding connectors |
Optical Filter | IR Cut Filter on |
Optical Center Accuracy | Positional accuracy in H and V directions: +/- 0.3 mm Rotational accuracy of H and V: +/- 1.5 deg. |
Material | Aluminum (AC) |
Lens Mount | C mount |
Connectors | RJ45 connector; Power/IO connector: HR10A-10R-6PB (Hirose) or equivalent |
Camera Mount Screws | Two 1/4” Tripod screw holes: (One on each top and bottom plate), Twelve M4 screws holes: (Four on each top and bottom plate, two on each side plate) |
Weight | Approx. 130 |
Operating Temperature | |
Minimum
|
Environmental Temperature -5°C |
Maximum
|
Camera housing temperature (top plate) shall not exceed 65⁰C (This corresponds to an environmental temperature of approximately 35°C) |
Storage Temperature | Environmental Temperature: -30°C to 65°C |
Vibration | 20Hz to 200Hz to 20Hz (5min./cycle), acceleration 10G, 3 directions 30 min. each |
Shock | Acceleration 38G, half amplitude 6ms, 3 directions 3 times each |
Standard Compliancy | EMS: EN61000-6-2, EMI: EN55011 |
RoHS | RoHS Compliant |