The STC-SC32POEHS is part of Sentech's Brand New Power over Ethernet High Speed GigE camera series. It features a 1/2" color VGA sensor, 122fps and communication over a 6 pin Hirose or Ethernet connector. The STC-SC32POEHS boasts a compact 35(w) x 35(H) x 55.9 (D) mm size, a user-programmable Area of Interest (AOI) and a Gamma Table that can be imported. This camera meets all industry standards for GigE Vision® and GenICam™, and is compatible with all standard industry drivers. The GigE PoEHS series is available now at an extremely low cost.
Features:
STC-SC32POEHS Specifications | |
Imager | 1/2” interline VGA color progressive CCD: ICX414AQ |
Total Picture Element | 659(H)x494(V) |
Active Picture Element | VGA: 648 (H) x 494 (V) |
Cell Size | 9.9 (H) x 9.9 (V) µm |
Scanning System | Progressive |
Vertical Frequency | 122.11786 Hz at full resolution 0.97814 to 419.03186 Hz adjustable via the communication (Frame rate depends on the AOI setting) Maximum frame rate (419.03186 Hz) is when vertical resolution AOI setting is 104. |
Horizontal Frequency | 64.19536KHz |
Pixel Frequency | 50.07272 MHz |
Noise Level | |
@ 8bit output
|
<= 3 Digit (Gain 0 dB) |
@ 10bit output
|
<= 12 Digit (Gain 0 dB) |
@ 12bit output
|
<= 48 Digit (gain 0 dB) |
Minimum Scene Illumination | 43.64 Lux at F1.2, 122.27770Hz |
Sync System | Internal |
Video Output | Digital 8 ,10 or 12 bit Raw Data or RGB 8 bit |
Interface | PoE: IEEE802.3af CLASS3 (1000BASE-T) |
Protocol | GigE Vision 1.2 and GeniCam 2.0 compliant |
Exposure Time | Preset continuous mode: 10 seconds to 16,777,216 seconds; Preset trigger mode: 10 seconds to 16,777,216 seconds; Pulse width mode: 10 seconds to Unlimited. |
ALC | Electronic iris and AGC (ON/OFF) |
Gain | 0 to 18.309 dB |
Gamma | Gamma 1.0 (Factory default) or downloadable gamma table |
AOI Function | Programmable AOI setting via the communication |
Smear Reduction | Selectable ON/OFF via the communication |
Color Interpolation | Available on RGB output |
White Balance Function | Auto, Manual, and push to set white balance is available on both Raw Data output and RGB output. |
Operation Mode | Edge preset trigger, pulse width trigger (unlimited exposure time) |
Communication | UART communication through Ethernet Port |
I/Os | One opt isolated input and two open collector outputs |
Power | |
Input Voltage
|
+10.8 to +26.4Vdc through power/IO connector or Power Over Ethernet; (Auto detection with power/IO connector prioritized) |
Consumption
|
12V: 3.2W / 2.9W, PoE: 3.4W / 3.1W |
Dimensions | 35 (W) x 35 (H) x 57.3 (D) mm excluding connectors |
Optical Filter | IR cut filter on |
Optical Center Accuracy | Positional accuracy in H and V directions: +/- 0.3 mm; Rotational accuracy of H and V: +/- 1.5 deg. |
Material | Aluminum (AC) |
Lens Mount | C Mount |
Connectors | RJ45 connector; Power/IO connector: HR10A-10R-6PB (Hirose) or equivalent |
Camera Mount Screws | Two ¼” Tripod screw holes (one each on top and bottom plate); Twelve M4 screw holes (four each on top, bottom, and two each on both side plates) |
Weight | Approx. 130 |
Operating Temperature | |
Minimum
|
Environmental Temperature: -5 deg. C |
Maximum
|
Environmental Temperature: 35 deg. C or camera housing temperature (Top Plate) : 65 deg. C |
Storage Temperature | Environmental Temperature: -30 to 65 deg. C |
Vibration | 20Hz to 200Hz to 20Hz (5min/cycle), acceleration 10G, 3 directions 30 min. each |
Shock | Acceleration 38G, half amplitude 6ms, 3 directions, 3 times each |
Standard Compliancy | EMS: EN61000-6-2, EMI: EN55011 |
RoHS | RoHS compliant |