Omron STC-MBS43U3V (STCMBS43U3V) USB3 Vision CMOS, 0.4 MP, Monochrome, Cased

Model No

STC-MBS43U3V

Image Sensor

1/2.9" 0.4M Progressive Monochrome CMOS (Sony: IMX287)

Shutter Type

Global

Active Picture Element

728 (H) x 544 (V)

Cell Size

6.9 (H) x 6.9 (V) µm

Sync System

External Trigger (Hardware, Software) / Free Run

Maximum Frame Rate

-

- 8Bit Output

527.1 fps (Frame Rate Priortized mode) / 439.9 fps (Image quality priortized mode)

- 10Bit Output

439.9 fps

- 10bit Packed output

439.9 fps

- 12Bit Output

322.1 fps

- 12bit Packed output

322.1 fps

ADC bit depth

10bit / 12bit

Video Format

8bits / 10bits / 12bits output (Support packed on 10bits / 12bits)

Noise Level

-

- 8Bit Output

Less than 6 digits (Gain 0 dB, Frame raye prortized) / Less than 3 digits (Gain 0 dB, Image Quality prirtized)

- 10bit / 10bit Packed Output

Less than 12 digits (Gain 0 dB)

- 12bit / 12bit Packed Output

Less than 48 digits (Gain 0 dB)

Sensitivity

8bits (Frame rate prioritized): 27 Lux 8bits (Image quality prioritized) / 10bits /12bits:108 Lux

Exposure Time

-

- 8Bit Output

1 µsecond to 16.777 seconds (Default: 1.77373 mseconds)

- 10Bit Output

1 µsecond to 16.777 seconds (Default: 1.77373 mseconds)

- 10bit Packed output

1 µsecond to 16.777 seconds (Default: 1.77373 mseconds)

- 12Bit Output

1 µsecond to 16.777 seconds (Default: 1.77373 mseconds)

- 12bit Packed output

1 µsecond to 16.777 seconds (Default: 1.77373 mseconds)

White Balance

N/A

ROI

Horizontal: 64 to 720 (704 on Packed) pixels / Vertical: 4 to 540 lines (Default: 720 x 540) Adjustable Steps for image size: 16 pixels in horizontal direction (64 pixels on Packed) / 4 lines in vertical direction Adjustable Steps for offset: 4 pixels in horizontal direction / 4 lines in vertical direction

Multi ROI

N/A

Gamma

Gamma Table = 0.1 to 4.0, Default = 1.0

Binning

N/A

Decimation

N/A

Flip Image

Horizontal / Vertical / Horizontal and Vertical / OFF

Defective Pixel Correction

Up to 256 points

Auto Image Control

-

- Auto Exposure

Support

- Auto Gain

Support

- Auto White Blance

N/A

Operational Mode

Edge-preset Trigger / Pulse width Trigger / Start Stop Trigger / Free run

User Setting Storage

Support

Communication

Through USB3.0 bus

Interface

USB 3.0 Super Speed (USB 3.0 Micro B)

Protocol

USB3 Vision® 1.0 , GenICam Standard Version (SFNC 2.2, PFNC 2.0) compliant and Sentech’s unique protocol (on Normal SDK / Trigger SDK)

Input / Output

Three GPIO, One Camera Hardware Reset

Power

-

- Input Voltage

+5V (typ.) (Conform to USB Standard)

- Consumption

Max: 3.4 W, Typ: 3.1 W

Dimensions

28 (W) x 28 (H) x 40 (D) mm (*1)

Optical Filter

No Optical Cut Filter

Optical Center Accuracy

Positional Accuracy in H and V directions: +/- 0.3 mm, Rotational accuracy of H and V: +/- 1.5 deg.

Material

Aluminum (AC)

Lens Mount

C Mount

Interface Connector

USB Connector: USB 3.0 MicroB type / I/O Connector: HR10A-7R-6PB (Hirose) or equivalent

Camera Mounting

M2 screw holes (Three on top, bottom and both side plate) M4 screws holes (Two on top, four on bottom plate)

Weight

Approx. 46g

Operational Temperature / Humidity

-

- Minimum

Environmental Temperature: 0 deg. C, Environmental Humidity: 0 to 85 %RH (No condensation)

- Maximum

Camera housing temperature (top plate) shall not exceed 54 deg. C (*1), Environmental Humidity: 0 to 85 %RH (No condensation)

Storage Temperature / Humidity

Environmental Temperature: -30 to +65 deg. C, Environmental Humidity: 0 to 90%

Vibration

20 Hz ~ 200 Hz ~ 20 Hz (5 min. /cycle), Acceleration 10G, XYZ 3 directions 30 minutes each

Shock

Acceleration 38 G, half amplitude 6 ms, XYZ 3 directions 3 times each

Standard Compliance

EMS: EN61000-6-2, EMI: EN55011

RoHS

RoHS Compliance